3D Printing and Design
100622Module 6: Post Processing and Quality
Q1(j). Which is a method of inspection? (i) Visual inspection (ii) Digital inspection (iii) Physical inspection (iv) All of the above20262m
Module 6: Post Processing and Quality
View this question on its own page →Which is a method of inspection?
(i) Visual inspection
(ii) Digital inspection
(iii) Physical inspection
(iv) All of the aboveWorked SolutionAnswer: (iv) All of the above
Printed parts are checked by visual inspection, digital inspection (3D scanning, CMM, CT) and physical inspection (gauges, calipers, mechanical tests).
Q6(b). What are the common faults in Additive Manufacturing equipment?20267m
Module 6: Post Processing and Quality
View this question on its own page →What are the common faults in Additive Manufacturing equipment?
Worked SolutionCommon Faults in Additive Manufacturing Equipment
Fault Cause Remedy Nozzle clogging Debris, wrong temperature, moisture in filament Clean or replace nozzle, dry filament, correct temperature Warping / poor bed adhesion Uneven cooling, dirty or unlevelled bed Heated bed, brim or raft, level the bed Layer shifting Loose belts, overheated drivers, mechanical obstruction Tighten belts, reduce speed, check motors Under-extrusion Partial clog, wrong flow, worn extruder gear Clean path, calibrate flow, replace gear Over-extrusion / blobs Flow too high, wrong filament diameter Calibrate extrusion multiplier Stringing Oozing during travel Enable retraction, lower temperature Layer separation (delamination) Low temperature, excess cooling Raise temperature, reduce fan Thermal runaway or temperature error Faulty heater or thermistor Replace sensor, enable thermal protection Dimensional inaccuracy Shrinkage, loose axes, uncalibrated steps/mm Calibrate, compensate scale Laser or optics faults (SLA, SLS) Dirty lens or mirror, misalignment Clean and recalibrate Powder or resin recoating issues Uneven recoater, contaminated material Level recoater, filter resin Software / G-code errors Corrupt file, wrong settings Reslice, update firmware MermaidDiagramRendering diagram…Exam tip
Group the faults as mechanical, thermal, material and software, and give cause and remedy for at least 6.
Q7(a). Why is post-processing required in Additive Manufacturing? Explain different post-processing techniques.20267m
Module 6: Post Processing and Quality
View this question on its own page →Why is post-processing required in Additive Manufacturing? Explain different post-processing techniques.
Worked SolutionPost-Processing in Additive Manufacturing
Why it is required
- Remove supports, loose powder or excess resin.
- Improve surface finish (staircase effect, layer lines).
- Improve dimensional accuracy and fit.
- Enhance mechanical properties (strength, density, stress relief).
- Add appearance: colour, coating, polish.
- Make the part functional, safe or biocompatible (sterilization).
MermaidDiagramRendering diagram…Technique Used for Support removal All processes; soluble supports (PVA, HIPS) for FDM Sanding and polishing FDM, SLA surface smoothing Vapour smoothing ABS with acetone vapour Bead / sand blasting Metal and nylon powder parts UV post-curing SLA, DLP resin parts Heat treatment, HIP Metal parts: remove residual stress, close pores Infiltration Binder jetting parts: strengthen with resin or metal Painting, dyeing, plating Appearance and protection Machining Critical dimensions and threads Exam tip
Give 4 reasons and classify techniques with examples for FDM, SLA and metal parts.
Q8(a). Explain the need for post-processing in 3D printing. Discuss both functional and aesthetic reasons with examples.20257m
Module 6: Post Processing and Quality
View this question on its own page →Explain the need for post-processing in 3D printing. Discuss both functional and aesthetic reasons with examples.
Worked SolutionNeed for Post-Processing in 3D Printing
Post-processing consists of operations performed after printing to obtain the required functional and aesthetic properties.
Functional reasons
- Remove supports: Makes the part usable and exposes required features.
- Improve dimensional accuracy: Finishing operations can remove small unwanted material.
- Increase surface quality: Smoothing can reduce roughness and friction.
- Improve mechanical properties: Curing, heat treatment, coating or other processes can improve strength, hardness or durability depending on the material.
- Improve chemical/environmental resistance: Coatings can protect surfaces.
- Prepare for assembly: Holes, interfaces and mating surfaces may need cleaning or finishing.
Aesthetic reasons
- Remove visible layer lines and print marks.
- Produce a smoother and more uniform appearance.
- Apply primer, paint, colour or protective coating.
- Improve gloss, texture or surface uniformity.
Examples
FDM parts may require support removal, sanding, polishing or acetone vapour smoothing for suitable materials. SLA parts generally require washing and UV post-curing. SLS parts require powder removal and may be polished, dyed or coated.
Thus, post-processing converts a freshly printed part into a component that meets its required functional and visual specifications.
Q8(b). Describe the steps involved in post-processing of 3D printed parts. Include cleaning, fixing, curing, surface finishing, and colouring techniques.20257m
Module 6: Post Processing and Quality
View this question on its own page →Describe the steps involved in post-processing of 3D printed parts. Include cleaning, fixing, curing, surface finishing, and colouring techniques.
Worked SolutionSteps in Post-Processing of 3D Printed Parts
1. Cleaning and support/powder removal
- FDM: Remove support structures mechanically or with suitable soluble-support methods.
- Material Jetting: Remove support material according to the material system.
- SLS/Powder-bed processes: Remove loose powder using brushing, air or appropriate powder-removal equipment.
- SLA: Wash the part to remove uncured resin.
2. Fixing and repair
Defects or surface gaps may be corrected using filling, gluing, welding or other material-compatible repair techniques.
3. Curing or hardening
SLA and some other resin-based parts are post-cured under controlled UV exposure to increase polymer conversion and achieve the intended properties.
4. Surface finishing
Common methods include:
- Sanding
- Polishing
- Tumbling
- Hydro dipping
- Epoxy coating
- Electroplating
- Vapour smoothing, such as acetone treatment for suitable thermoplastics
5. Colouring and coating
The surface may be primed and painted or treated with dyes/coatings to obtain the required colour, appearance and protection.
Final result
The sequence is generally clean/remove supports or powder → repair/fix → cure/harden where required → surface finish → prime/paint/coat. The exact sequence depends on the printing material and intended application.
Q9(a). Explain various inspection and testing methods (digital, visual, physical) used in 3D printing. What are common defects and their causes?20257m
Module 6: Post Processing and Quality
View this question on its own page →Explain various inspection and testing methods (digital, visual, physical) used in 3D printing. What are common defects and their causes?
Worked SolutionInspection, Testing, Defects and Their Causes
Inspection and testing verify that a printed component satisfies dimensional, visual and functional requirements.
1. Digital inspection
The manufactured part can be measured or scanned digitally and compared with the CAD model. Methods include 3D scanning, dimensional metrology and digital deviation maps. These methods help identify dimensional errors and geometric deviations.
2. Visual inspection
The surface is examined for visible defects such as cracks, warping, layer separation, roughness, incomplete features, discoloration and poor support removal.
3. Physical inspection/testing
Depending on the application, tests can include dimensional measurement, hardness, tensile testing, compression testing, density/porosity measurement and functional fit tests.
Common defects and causes
Defect Typical causes Warping Thermal contraction, poor bed adhesion, unsuitable temperature or cooling Layer separation/delamination Poor interlayer bonding, low temperature, contamination or excessive cooling Stringing Incorrect retraction or temperature settings in FDM Under-extrusion Poor filament feed, clogged nozzle or incorrect extrusion settings Stair-stepping Excessive layer thickness or unfavorable orientation Voids/porosity Insufficient fusion, poor powder quality or incorrect process parameters Surface roughness Layer height, powder characteristics, scanning/extrusion conditions or inadequate finishing Conclusion
A combination of digital, visual and physical inspection gives a more reliable assessment because no single method detects every possible defect.
Q9(a). Write a short note on: Vapour smoothing using acetone treatment and its application in 3D printing20267m
Module 6: Post Processing and Quality
View this question on its own page →Write a short note on: Vapour smoothing using acetone treatment and its application in 3D printing
Worked SolutionShort Note: Vapour Smoothing with Acetone
Vapour smoothing is a chemical post-processing method mainly for ABS (and ASA) FDM parts. Acetone vapour softens the outer surface, which flows slightly and smooths layer lines, then re-hardens.
MermaidDiagramRendering diagram…Procedure
- Place the part on a stand in a sealed container with a little acetone below.
- Warm gently to produce vapour (or use a cold method with a soaked tissue).
- Expose for a short, controlled time (minutes).
- Remove and let it dry fully.
Advantages and cautions
- Gives glossy, smooth, watertight surface and better layer bonding.
- Over-exposure causes loss of fine detail and dimensional change.
- Acetone is highly flammable and toxic: use in ventilated area, away from flame, with PPE.
Applications
Enclosures, display models, fluidic parts, cosmetic prototypes, casting patterns. PLA is not affected by acetone (use other solvents).
Exam tip
Write the principle, the four-step procedure and the safety note.