Bio MEMS

117602
Back to Bio MEMS

Module 3: Fabrication Techniques

  1. Q1(a). Which sequence most appropriately represents the basic microfabrication flow? (i) Etching → Lithography → Deposition (ii) Deposition → Lithography → Etching (iii) Lithography → Etching → Packaging only (iv) Packaging → Lithography → Deposition20262m

    Module 3: Fabrication Techniques

    Which sequence most appropriately represents the basic microfabrication flow?

    (i) Etching → Lithography → Deposition
    (ii) Deposition → Lithography → Etching
    (iii) Lithography → Etching → Packaging only
    (iv) Packaging → Lithography → Deposition

    View this question on its own page →
    Worked Solution

    Answer: (ii) Deposition → Lithography → Etching

    A thin film is deposited first, lithography then defines the pattern in photoresist, and etching transfers that pattern into the film. Packaging comes last, after the device is released and tested.

  2. Q1(b). SU-8 is an example of: (i) Positive Photoresist (ii) Negative Photoresist (iii) Electron Beam Resist (iv) Inorganic Resist2025?m

    Module 3: Fabrication Techniques

    SU-8 is an example of:

    (i) Positive Photoresist
    (ii) Negative Photoresist
    (iii) Electron Beam Resist
    (iv) Inorganic Resist

    View this question on its own page →
    Worked Solution

    Answer: (ii) Negative Photoresist

    SU-8 is an epoxy-based negative photoresist. The exposed regions polymerize and become resistant to the developer, allowing high-aspect-ratio microstructures to be formed.

  3. Q1(d). The LIGA process utilizes which type of radiation for lithography? (i) Ultraviolet (UV) (ii) X-ray (iii) Infrared (iv) Visible Light2025?m

    Module 3: Fabrication Techniques

    The LIGA process utilizes which type of radiation for lithography?

    (i) Ultraviolet (UV)
    (ii) X-ray
    (iii) Infrared
    (iv) Visible Light

    View this question on its own page →
    Worked Solution

    Answer: (ii) X-ray

    LIGA uses deep X-ray lithography to create high-aspect-ratio microstructures. The X-rays expose a thick resist, traditionally PMMA, through a mask.

  4. Q1(f). In UV lithography, ultraviolet radiation is primarily used to: (i) Pattern a photosensitive material (ii) Pump fluid directly (iii) Concentrate biological cells (iv) Measure fluid pressure20262m

    Module 3: Fabrication Techniques

    In UV lithography, ultraviolet radiation is primarily used to:

    (i) Pattern a photosensitive material
    (ii) Pump fluid directly
    (iii) Concentrate biological cells
    (iv) Measure fluid pressure

    View this question on its own page →
    Worked Solution

    Answer: (i) Pattern a photosensitive material

    UV light changes the solubility of the photoresist in the exposed regions, which defines the pattern after development.

  5. Q1(g). A major objective of lithography in MEMS fabrication is to achieve: (i) Controlled pattern definition (ii) Fluid sterilization (iii) Cell growth only (iv) Mechanical packaging only20262m

    Module 3: Fabrication Techniques

    A major objective of lithography in MEMS fabrication is to achieve:

    (i) Controlled pattern definition
    (ii) Fluid sterilization
    (iii) Cell growth only
    (iv) Mechanical packaging only

    View this question on its own page →
    Worked Solution

    Answer: (i) Controlled pattern definition

    Lithography fixes the size, shape and position of features, so later etching or deposition acts only where intended.

  6. Q5(a). Explain the fabrication steps for high-aspect-ratio structures using SU-8 photoresist and Ultraviolet (UV) lithography.20257m

    Module 3: Fabrication Techniques

    Explain the fabrication steps for high-aspect-ratio structures using SU-8 photoresist and Ultraviolet (UV) lithography.

    View this question on its own page →
    Worked Solution

    SU-8 High-Aspect-Ratio Structures Using UV Lithography

    SU-8 is a negative epoxy-based photoresist capable of forming thick, high-aspect-ratio structures.

    Fabrication steps

    1. Substrate preparation: Clean and dehydrate the silicon/glass substrate.
    2. SU-8 coating: Dispense SU-8 and spin coat it to the required thickness. For very thick layers, multiple coating steps may be used.
    3. Soft bake: Heat the coated wafer to remove solvent.
    4. Mask alignment: Place the patterned photomask over the wafer.
    5. UV exposure: Expose the SU-8 through the mask. Exposed regions undergo cross-linking.
    6. Post-exposure bake: Further cross-link the exposed regions.
    7. Development: Developer removes the unexposed SU-8, leaving the patterned high-aspect-ratio structures.
    8. Rinse and dry: Remove developer residue.
    9. Hard bake, if required: Improves stability and mechanical robustness.

    Why SU-8 is suitable

    It provides thick films, high aspect ratios, good chemical resistance, good mechanical strength and relatively high resolution, making it useful for microchannels, molds and microstructures.

  7. Q5(a). Explain the basic principle of lithography.20267m

    Module 3: Fabrication Techniques

    Explain the basic principle of lithography.

    View this question on its own page →
    Worked Solution

    Basic principle of lithography

    Lithography (Greek: lithos = stone, graphein = to write) transfers a designed pattern from a master (mask or beam) into a radiation-sensitive layer, the resist, on a substrate. The resist is then a temporary stencil for etching, deposition or doping.

    MermaidDiagram
    Rendering diagram…

    Working idea

    Radiation (UV, electron beam, X-ray) changes the chemistry of the resist.

    • Positive resist: the exposed region becomes soluble and is washed away.
    • Negative resist: the exposed region cross-links and stays.

    Types of lithography

    Type Radiation Feature
    Photolithography UV light (g-line, i-line, DUV) Workhorse of MEMS; low cost
    Electron-beam Focused electrons Nanometre resolution; serial, slow, no mask
    X-ray (LIGA) Synchrotron X-rays Very tall, high-aspect-ratio structures
    Soft lithography Elastomer stamp (PDMS) Cheap microfluidics, replica moulding
    Nanoimprint Mechanical embossing High-resolution replication

    Key parameters

    Resolution R ≈ k₁λ/NA, depth of focus, alignment accuracy, resist sensitivity and contrast.

    Exam tip

    Define lithography, state the positive/negative idea, then list the types in a table.

  8. Q5(b). Write a detailed note on X-ray lithography and the LIGA process. What are its advantages?20257m

    Module 3: Fabrication Techniques

    Write a detailed note on X-ray lithography and the LIGA process. What are its advantages?

    View this question on its own page →
    Worked Solution

    X-ray Lithography and LIGA

    X-ray lithography uses short-wavelength, high-energy X-rays to transfer a mask pattern into a thick resist. The short wavelength provides low diffraction and enables high-resolution, high-aspect-ratio structures.

    LIGA

    LIGA is a German acronym derived from Lithographie, Galvanoformung, Abformung (lithography, electroplating and molding).

    Process

    1. Coat a conductive substrate with a thick X-ray-sensitive resist such as PMMA.
    2. Align a patterned X-ray mask.
    3. Expose the resist using deep X-rays.
    4. Develop the resist to form deep cavities/columns.
    5. Electroplate metal into the resist mold.
    6. Remove the resist to obtain a metal microstructure.
    7. The metal structure can also serve as a mold for replication.

    Advantages

    • Very high aspect ratio.
    • Nearly vertical sidewalls.
    • High dimensional accuracy.
    • Excellent replication capability.
    • Suitable for relatively thick microstructures.
    • Useful for microgears, nozzles, molds and other precision MEMS structures.

    Limitation

    The process requires specialized X-ray sources and masks, making it expensive and less accessible than conventional UV lithography.

  9. Q5(b). Explain UV lithography for SU-8. Describe the major steps involved in pattern formation.20267m

    Module 3: Fabrication Techniques

    Explain UV lithography for SU-8. Describe the major steps involved in pattern formation.

    View this question on its own page →
    Worked Solution

    UV lithography with SU-8: pattern formation

    SU-8 is an epoxy-based, chemically amplified negative photoresist (EPON SU-8 resin with a photoacid generator in a solvent). UV exposure releases acid that triggers cross-linking during the post-exposure bake. It gives thick films and very high-aspect-ratio structures.

    MermaidDiagram
    Rendering diagram…

    Steps

    1. Substrate preparation: clean and dehydrate; an adhesion layer may be used.
    2. Spin coating: spin speed and SU-8 grade set the thickness (about 1 µm to several hundred µm).
    3. Soft bake: evaporates solvent; a slow ramp avoids cracking.
    4. UV exposure: near-UV (i-line, 365 nm) through a mask; thicker films need a larger dose.
    5. Post-exposure bake (PEB): acid in the exposed region diffuses and cross-links the epoxy.
    6. Development: unexposed SU-8 dissolves in a developer such as PGMEA.
    7. Rinse and dry: isopropanol rinse, nitrogen dry.
    8. Hard bake (optional): improves stability and reduces cracks.

    Why SU-8 for BioMEMS

    • Aspect ratios above 20:1 are achievable.
    • Chemically and thermally stable once cured.
    • Used as the master mould for PDMS soft lithography and for permanent channels.

    Exam tip

    Stress that SU-8 is negative: the exposed region stays and the unexposed region dissolves.

  10. Q9(b). Write a short note on: Thin-film deposition techniques20267m

    Module 3: Fabrication Techniques

    Write a short note on: Thin-film deposition techniques

    View this question on its own page →
    Worked Solution

    Short note: Thin-film deposition techniques

    Thin films (nm to a few µm) form the structural, sacrificial, insulating and conducting layers of MEMS. Deposition methods fall into two groups.

    MermaidDiagram
    Rendering diagram…
    Method Principle Typical films
    Evaporation (PVD) Heated source vaporises in vacuum and condenses on the substrate Al, Au contacts
    Sputtering (PVD) Ion bombardment ejects target atoms that coat the substrate Metals, ZnO, PZT
    LPCVD Gas reaction at low pressure and high temperature; uniform films Polysilicon, silicon nitride
    PECVD Plasma allows reaction at a lower temperature Silicon oxide, nitride
    Thermal oxidation Silicon reacts with O₂ or steam at high temperature SiO₂
    Electroplating Metal ions deposited from solution by current Thick Ni, Cu, Au (LIGA)
    Spin coating Liquid spread by centrifugal force, then cured Photoresist, polymers, SU-8

    Selection factors

    Film uniformity, step coverage, stress, deposition temperature, rate and cost.

    Exam tip

    Divide into PVD and CVD, then give one-line principles and examples in a table.