2025 question paper

Robotics Mechanics, Kinematics and Dynamics

25 questions

  1. Q1(a). Robot anatomy mainly includes: (i) Sensors and controllers (ii) Links, joints, actuators, and controller (iii) Power supply only (iv) End effector only20252m

    Module 1: Introduction-I

    Robot anatomy mainly includes:
    (i) Sensors and controllers
    (ii) Links, joints, actuators, and controller
    (iii) Power supply only
    (iv) End effector only

    View this question on its own page →
    Worked Solution

    Correct answer: (ii) Links, joints, actuators, and controller. Robot anatomy describes the structural and functional components forming the manipulator and its motion system: links connected by joints, actuators, end effector, sensors, and controller.

  2. Q1(b). The workspace of a robot is: (i) Area occupied by robot base (ii) Maximum volume reachable by end effector (iii) Area covered by sensors (iv) Controller memory space20252m

    Module 1: Introduction-I

    The workspace of a robot is:
    (i) Area occupied by robot base
    (ii) Maximum volume reachable by end effector
    (iii) Area covered by sensors
    (iv) Controller memory space

    View this question on its own page →
    Worked Solution

    Correct answer: (ii) Maximum volume reachable by end effector. A robot workspace is the set of positions (and, for a dexterous workspace, orientations) that the end effector can reach subject to joint limits and physical constraints.

  3. Q1(c). SCARA robots are best suited for: (i) Heavy lifting (ii) Welding operations (iii) Pick and place operations (iv) Mobile navigation20252m

    Module 1: Introduction-I

    SCARA robots are best suited for:
    (i) Heavy lifting
    (ii) Welding operations
    (iii) Pick and place operations
    (iv) Mobile navigation

    View this question on its own page →
    Worked Solution

    Correct answer: (iii) Pick and place operations. SCARA robots provide selective compliance in the horizontal plane and stiffness vertically, making them effective for high-speed assembly and pick-and-place tasks.

  4. Q1(d). Transformation between coordinate frames is achieved using: (i) Velocity equations (ii) Jacobian matrix (iii) Homogeneous transformation matrix (iv) Sensor signals20252m

    Module 1: Introduction-I

    Transformation between coordinate frames is achieved using:
    (i) Velocity equations
    (ii) Jacobian matrix
    (iii) Homogeneous transformation matrix
    (iv) Sensor signals

    View this question on its own page →
    Worked Solution

    Correct answer: (iii) Homogeneous transformation matrix. A 4×4 homogeneous transform combines rotation and translation to express one coordinate frame relative to another and transform points between frames.

  5. Q1(e). Roll-Pitch-Yaw (RPY) angles describe: (i) Robot speed (ii) Robot orientation (iii) Robot workspace (iv) Robot power20252m

    Module 1: Introduction-I

    Roll-Pitch-Yaw (RPY) angles describe:
    (i) Robot speed
    (ii) Robot orientation
    (iii) Robot workspace
    (iv) Robot power

    View this question on its own page →
    Worked Solution

    Correct answer: (ii) Robot orientation. Roll, pitch, and yaw are three angles describing orientation relative to coordinate axes, commonly implemented as a specified sequence of rotations.

  6. Q1(f). Which of the following is a position sensor? (i) Thermocouple (ii) Encoder (iii) Pressure gauge (iv) Flow meter20252m

    Module 2: Introduction-II

    Which of the following is a position sensor?
    (i) Thermocouple
    (ii) Encoder
    (iii) Pressure gauge
    (iv) Flow meter

    View this question on its own page →
    Worked Solution

    Correct answer: (ii) Encoder. Encoders convert shaft/linear motion into electrical pulses or coded position data, enabling position and speed feedback.

  7. Q1(g). Pneumatic actuators use: (i) Hydraulic oil (ii) Compressed air (iii) Electrical current (iv) Steam20252m

    Module 2: Introduction-II

    Pneumatic actuators use:
    (i) Hydraulic oil
    (ii) Compressed air
    (iii) Electrical current
    (iv) Steam

    View this question on its own page →
    Worked Solution

    Correct answer: (ii) Compressed air. Pneumatic actuators use pressurised air to generate linear or rotary motion.

  8. Q1(h). A kinematic pair is a connection between: (i) Two sensors (ii) Two links (iii) Two actuators (iv) Link and controller20252m

    Module 3: Robot Mechanisms

    A kinematic pair is a connection between:
    (i) Two sensors
    (ii) Two links
    (iii) Two actuators
    (iv) Link and controller

    View this question on its own page →
    Worked Solution

    Correct answer: (ii) Two links. A kinematic pair is a joint/connection between two links that constrains their relative motion in a defined way.

  9. Q1(i). SCARA robots are preferred for inverse kinematics because they are: (i) Highly nonlinear (ii) Structurally simple (iii) Over-actuated (iv) Redundant20252m

    Module 4: Robot Kinematics

    SCARA robots are preferred for inverse kinematics because they are:
    (i) Highly nonlinear
    (ii) Structurally simple
    (iii) Over-actuated
    (iv) Redundant

    View this question on its own page →
    Worked Solution

    Correct answer: (ii) Structurally simple. SCARA inverse kinematics is comparatively straightforward because its joint arrangement separates planar positioning from vertical motion/rotation.

  10. Q1(j). Workspace fixtures are used to: (i) Increase robot speed (ii) Improve accuracy and repeatability (iii) Increase payload (iv) Reduce joint angles20252m

    Module 1: Introduction-I

    Workspace fixtures are used to:
    (i) Increase robot speed
    (ii) Improve accuracy and repeatability
    (iii) Increase payload
    (iv) Reduce joint angles

    View this question on its own page →
    Worked Solution

    Correct answer: (ii) Improve accuracy and repeatability. Fixtures locate and constrain workpieces consistently, reducing placement variation and improving repeatability of robot operations.

  11. Budget App•POCKETLY

    Pocketly on Android

    Log daily food, travel, and hostel expenses instantly. Set monthly spending limits and see where your money goes without complex spreadsheets.

    Install Pocketly
  12. Q2(a). Explain different types of robot workspaces and factors affecting workspace.20257m

    Module 1: Introduction-I

    Explain different types of robot workspaces and factors affecting workspace.

    View this question on its own page →
    Worked Solution

    Types of robot workspace: (1) Reachable workspace: all positions the end effector can reach in at least one orientation. (2) Dexterous workspace: positions at which all required orientations are achievable. Workspace may be spherical, cylindrical, or roughly box-shaped depending on joint layout. Factors: link lengths; revolute/prismatic joint arrangement; joint-angle and stroke limits; self-collision; obstacles; end-effector dimensions; mechanical stops; singularities; and mounting/base geometry. Workspace can be analysed geometrically from forward kinematics or numerically by sampling joint configurations and plotting reachable points. The usable workspace is smaller than the theoretical one because of collision, load, accuracy, and safety constraints.

  13. Q2(b). Explain coordinate frames used in robotics.20257m

    Module 1: Introduction-I

    Explain coordinate frames used in robotics.

    View this question on its own page →
    Worked Solution

    A coordinate frame is a reference origin plus three mutually perpendicular axes used to express position and orientation. Robotics commonly uses the world/base frame, joint/link frames, tool/end-effector frame, and workpiece/object frame. A point is represented by coordinates relative to a chosen frame. To convert between frames, use a homogeneous transform T = [[R,p],[0,1]], where R is a 3×3 rotation matrix and p is a 3×1 translation vector. If ^A T_B transforms coordinates from frame B to A, then ^A p = ^A T_B ^B p. For a serial chain, transformations multiply in order: ^0T_n = ^0T_1 ^1T_2 … ^(n−1)T_n. Frame conventions must be consistent.

  14. Q3(a). Describe the various types of actuators used in robotic systems.20257m

    Module 2: Introduction-II

    Describe the various types of actuators used in robotic systems.

    View this question on its own page →
    Worked Solution

    Actuator types: (1) Electric: DC, brushless DC, AC, servo, and stepper motors; clean and controllable, widely used in precision robots. (2) Hydraulic: pressurised fluid drives cylinders/motors; very high force and power density, but leaks and maintenance are concerns. (3) Pneumatic: compressed air drives cylinders or rotary actuators; fast, simple, and inexpensive, but compressibility limits precision/stiffness. (4) Piezoelectric: voltage-induced deformation gives very small, precise motion, often for micro-positioning. (5) Shape-memory/alloy or other smart-material actuators: compact but often slower and thermally limited. Selection depends on load, speed, precision, stroke, duty cycle, energy, environment, cost, and safety.

  15. Q3(b). What is meant by RPY configuration in robotics?20257m

    Module 4: Robot Kinematics

    What is meant by RPY configuration in robotics?

    View this question on its own page →
    Worked Solution

    RPY represents orientation using three rotations: roll about the x-axis, pitch about the y-axis, and yaw about the z-axis, under a stated convention. For one common fixed-axis convention, R = Rz(ψ) Ry(θ) Rx(φ), where φ is roll, θ pitch, and ψ yaw. The matrices are multiplied in the specified order; rotation order matters because 3-D rotations do not generally commute. RPY is intuitive for describing tool orientation, but it can suffer gimbal lock at certain pitch angles and is convention-dependent. Always state whether rotations are intrinsic/body-fixed or extrinsic/world-fixed.

  16. Q4(a). How do Jacobian matrices relate joint velocities to end-effector velocities in robotic arms? Calculate the Jacobian for a 2 DOF planar manipulator.20257m

    Module 3: Robot Mechanisms

    How do Jacobian matrices relate joint velocities to end-effector velocities in robotic arms? Calculate the Jacobian for a 2 DOF planar manipulator.

    View this question on its own page →
    Worked Solution

    For a planar 2R manipulator with link lengths l₁,l₂ and joint angles θ₁,θ₂, end-effector position is x=l₁cosθ₁+l₂cos(θ₁+θ₂), y=l₁sinθ₁+l₂sin(θ₁+θ₂). Differentiating gives [ẋ,ẏ]ᵀ = J[θ̇₁,θ̇₂]ᵀ, where J = [[−l₁sinθ₁−l₂sin(θ₁+θ₂), −l₂sin(θ₁+θ₂)], [l₁cosθ₁+l₂cos(θ₁+θ₂), l₂cos(θ₁+θ₂)]]. The Jacobian maps joint velocity to Cartesian velocity; determinant l₁l₂sinθ₂, so the arm is singular when θ₂ = 0 or π (links collinear). It is used for velocity control, force mapping, and singularity analysis.

  17. Q4(b). Explain the classification of kinematic pairs with neat sketches and practical examples.20257m

    Module 3: Robot Mechanisms

    Explain the classification of kinematic pairs with neat sketches and practical examples.

    View this question on its own page →
    Worked Solution

    A kinematic pair is a connection between two links that permits specified relative motion. By contact: lower pairs have surface contact (revolute hinge, prismatic slider); higher pairs have point/line contact (cam-follower, gears). By relative motion: revolute (rotation), prismatic (translation), helical (screw motion), cylindrical (rotation plus translation along one axis), spherical (ball-and-socket), and planar. By closure: closed pairs remain connected by geometry; force-closed pairs rely on external force such as a spring. Sketch examples: hinge pin rotating in a bearing; slider moving in a guide; meshing gear teeth. Pair type determines degrees of freedom and constraints in the robot mechanism.

  18. Q5(a). How are the velocity and acceleration of moving frames in a robotic manipulator computed, and why are they important for dynamic analysis?20257m

    Module 4: Robot Kinematics

    How are the velocity and acceleration of moving frames in a robotic manipulator computed, and why are they important for dynamic analysis?

    View this question on its own page →
    Worked Solution

    For a moving frame, position is described by a time-dependent transform T(t) = [R(t),p(t);0,1]. Linear velocity is v = dp/dt. Angular velocity can be obtained from ṘRᵀ (space-frame convention) or RᵀṘ (body-frame convention), which yields a skew-symmetric matrix [ω]×. For a point fixed on a rotating link, v = v_origin + ω×r. Acceleration includes translational acceleration and rotational terms: a = a_origin + α×r + ω×(ω×r) for a fixed point relative to the link; relative motion adds Coriolis and relative-acceleration terms. These quantities are needed for inertial forces, torque calculation, trajectory control, and dynamic simulation.

  19. Q5(b). Explain the types of constrained motion with suitable examples from robot mechanisms.20257m

    Module 3: Robot Mechanisms

    Explain the types of constrained motion with suitable examples from robot mechanisms.

    View this question on its own page →
    Worked Solution

    Constrained motion types: (1) Completely constrained: relative motion is limited to one definite form, e.g. a rectangular slider in a matching guide. (2) Incompletely constrained: more than one relative motion is possible, e.g. a circular shaft in a circular hole may rotate and slide axially. (3) Successfully constrained: motion is made definite by an external force or arrangement, e.g. a vertical shaft constrained by gravity/thrust bearing or a spring-loaded follower. In robot mechanisms, joints intentionally constrain degrees of freedom so the mechanism has predictable motion; correct constraints prevent unwanted movement and determine mobility.

  20. Q6(a). Explain the Denavit-Hartenberg (DH) notation and derive the general forward kinematic equations for a serial robotic manipulator.20257m

    Module 4: Robot Kinematics

    Explain the Denavit-Hartenberg (DH) notation and derive the general forward kinematic equations for a serial robotic manipulator.

    View this question on its own page →
    Worked Solution

    The Denavit–Hartenberg (DH) convention describes each link-to-link transform with four parameters: aᵢ (link length), αᵢ (link twist), dᵢ (link offset), and θᵢ (joint angle). Under the standard convention, Aᵢ = Rot(z,θᵢ) Trans(z,dᵢ) Trans(x,aᵢ) Rot(x,αᵢ) = [[cθ,−sθcα,sθsα,a cθ],[sθ,cθcα,−cθsα,a sθ],[0,sα,cα,d],[0,0,0,1]]. For an n-link serial arm, base-to-tool transform is T₀ⁿ = A₁A₂…Aₙ. The upper-left 3×3 block gives orientation; the last column gives position. Joint variables are θᵢ for revolute joints and dᵢ for prismatic joints. DH results depend on the chosen convention and frame assignment.

  21. Q6(b). Derive the forward kinematic equations of a four-axis SCARA robot using DH parameters.20257m

    Module 4: Robot Kinematics

    Derive the forward kinematic equations of a four-axis SCARA robot using DH parameters.

    View this question on its own page →
    Worked Solution

    For a typical four-axis SCARA, joints are R–R–P–R: two revolute joints position the arm in the horizontal plane, a prismatic joint moves vertically, and a final revolute joint sets tool rotation. With link lengths a₁,a₂ and angles θ₁,θ₂, x=a₁cosθ₁+a₂cos(θ₁+θ₂), y=a₁sinθ₁+a₂sin(θ₁+θ₂), z is set by the prismatic coordinate (sign depends on DH convention), and tool yaw φ=θ₁+θ₂+θ₄ (plus any fixed frame offset). The homogeneous transform is T₀⁴=A₁A₂A₃A₄ using each link’s DH parameters. Exact signs and offsets depend on the chosen frame assignment; define that convention before deriving the final matrix.

  22. Budget App•POCKETLY

    Pocketly on Android

    Log daily food, travel, and hostel expenses instantly. Set monthly spending limits and see where your money goes without complex spreadsheets.

    Install Pocketly
  23. Q7(a). Explain workspace analysis and discuss the factors affecting the workspace of an industrial robot.20257m

    Module 1: Introduction-I

    Explain workspace analysis and discuss the factors affecting the workspace of an industrial robot.

    View this question on its own page →
    Worked Solution

    Workspace analysis determines all reachable end-effector positions/orientations. Geometric analysis uses link lengths and joint limits; forward kinematics maps joint configurations to Cartesian positions; numerical sampling can plot the reachable region. Reachable workspace includes positions attainable in at least one orientation, while dexterous workspace allows all required orientations. Factors include link lengths, joint types and limits, base mounting, end-effector geometry, collisions, singularities, payload/deflection, and obstacles. The practical workspace is smaller than the theoretical workspace because safe approach directions and accuracy constraints must be considered.

  24. Q7(b). Compare joint space and Cartesian space trajectory planning techniques.20257m

    Module 4: Robot Kinematics

    Compare joint space and Cartesian space trajectory planning techniques.

    View this question on its own page →
    Worked Solution

    Joint-space planning: interpolate joint variables from start to goal. It is computationally simpler and can avoid Cartesian path singularities, but the end-effector path is generally curved and obstacles must be checked in workspace. Cartesian-space planning: specify a path for end-effector position/orientation, then use inverse kinematics at points along it. It gives predictable tool paths for welding, cutting, and painting, but inverse kinematics may be expensive, have multiple/no solutions, and encounter singularities. Both require velocity/acceleration limits and smooth interpolation (e.g. cubic/quintic polynomials or trapezoidal profiles). Choose based on task accuracy, obstacle clearance, and manipulator constraints.

  25. Q8(a). Derive the Lagrange-Euler dynamic formulation in the context of robotic manipulators. What are generalized robotic coordinates and why are they important in this formulation?20257m

    Module 6: Manipulator Dynamics

    Derive the Lagrange-Euler dynamic formulation in the context of robotic manipulators. What are generalized robotic coordinates and why are they important in this formulation?

    View this question on its own page →
    Worked Solution

    Let generalized coordinates be q = [q₁,…,qₙ]ᵀ, with each qᵢ a revolute angle or prismatic displacement. Define Lagrangian L = K − P, where K and P are total kinetic and potential energy. For each coordinate, the Lagrange–Euler equation is d/dt(∂L/∂q̇ᵢ) − ∂L/∂qᵢ = τᵢ, with non-conservative forces included as needed. In vector form: M(q)q̈ + C(q,q̇)q̇ + g(q) + friction = τ. M is the inertia matrix; C represents Coriolis/centrifugal terms; g is gravity torque; τ is actuator input. Generalized coordinates compactly describe configuration and make it possible to derive coupled equations of motion for multi-link manipulators.

  26. Q8(b). Explain the expressions for kinetic energy and potential energy of robot links.20257m

    Module 6: Manipulator Dynamics

    Explain the expressions for kinetic energy and potential energy of robot links.

    View this question on its own page →
    Worked Solution

    For a rigid link i with centre-of-mass linear velocity vᵢ and angular velocity ωᵢ, kinetic energy is Kᵢ = ½mᵢvᵢᵀvᵢ + ½ωᵢᵀIᵢωᵢ, where mᵢ is mass and Iᵢ is the inertia tensor about the centre of mass (expressed in the same frame as ωᵢ). Total kinetic energy is K = ΣKᵢ. Gravitational potential energy is Pᵢ = mᵢ g hᵢ, where hᵢ is the centre-of-mass height relative to a chosen datum; P = Σmᵢghᵢ. These energies are used in the Lagrange–Euler formulation to obtain actuator torques. Rotational inertia must be transformed consistently between link and base frames.

  27. Q9(a). Write short notes on any two of the following: Robot Anatomy; Robot Sensors; Kinematic Pairs; Jacobian Matrix.20257m

    Module 1: Introduction-I

    Write short notes on any two of the following: Robot Anatomy; Robot Sensors; Kinematic Pairs; Jacobian Matrix.

    View this question on its own page →
    Worked Solution

    Robot anatomy: Base, links, joints, actuators, sensors, controller, and end effector form the robot structure. Joint type and link geometry determine degrees of freedom, workspace, and stiffness. Robot sensors: Encoders measure joint position; gyroscopes/accelerometers estimate motion; proximity and vision sensors detect objects; force/torque and tactile sensors support compliant interaction. Feedback improves accuracy and safety. Kinematic pairs: Connections between links permitting defined relative motion, e.g. revolute hinge, prismatic slider, cylindrical or spherical joint. Their constraints determine mechanism mobility. Jacobian matrix: J maps joint rates to end-effector velocity, v=J(q)q̇, and relates end-effector wrench to joint torque via τ=JᵀF. It supports velocity control, force mapping, and singularity analysis. This paper asks any two notes; these summaries cover all four for revision.

Official AppAndroid App

PYQDeck for Android

Solve BEU previous-year exam papers anywhere, anytime. Fast search, offline paper viewing, and step-by-step solutions designed specifically for your phone.