2025 question paper

Robotics Sensors and Actuators

25 questions

  1. Q1(a). Which sensor is most suitable for measuring angular velocity in robots? (i) Accelerometer (ii) Gyroscope (iii) Potentiometer (iv) Proximity sensor20252m

    Module 1: Sensor classifications and characteristics

    Which sensor is most suitable for measuring angular velocity in robots?
    (i) Accelerometer
    (ii) Gyroscope
    (iii) Potentiometer
    (iv) Proximity sensor

    View this question on its own page →
    Worked Solution

    Correct answer: (ii) Gyroscope. A gyroscope measures angular velocity. An accelerometer measures linear acceleration (and can help estimate tilt under suitable conditions); a potentiometer measures position by resistance change; a proximity sensor detects nearby objects.

  2. Q1(b). Load cells are commonly used as: (i) Position sensors (ii) Velocity sensors (iii) Force sensors (iv) Temperature sensors20252m

    Module 3: Force and Torque measurment

    Load cells are commonly used as:
    (i) Position sensors
    (ii) Velocity sensors
    (iii) Force sensors
    (iv) Temperature sensors

    View this question on its own page →
    Worked Solution

    Correct answer: (iii) Force sensors. A load cell converts applied force or weight into an electrical output, commonly using strain gauges whose resistance changes with deformation.

  3. Q1(c). In a servo motor system, feedback is generally provided by: (i) Ultrasonic sensor (ii) Force sensor (iii) Encoder or potentiometer (iv) IR sensor20252m

    Module 2: Position and velocity measurment

    In a servo motor system, feedback is generally provided by:
    (i) Ultrasonic sensor
    (ii) Force sensor
    (iii) Encoder or potentiometer
    (iv) IR sensor

    View this question on its own page →
    Worked Solution

    Correct answer: (iii) Encoder or potentiometer. Servo control uses position feedback from an encoder or potentiometer to compare actual position with the command and reduce the error.

  4. Q1(d). Ultrasonic sensors are least effective on: (i) Soft surfaces (ii) Rough surfaces (iii) Transparent objects (iv) Metallic objects20252m

    Module 1: Sensor classifications and characteristics

    Ultrasonic sensors are least effective on:
    (i) Soft surfaces
    (ii) Rough surfaces
    (iii) Transparent objects
    (iv) Metallic objects

    View this question on its own page →
    Worked Solution

    Correct answer: (iii) Transparent objects is the expected general answer for many ultrasonic sensors. Ultrasonic sensing depends on sound reflection, not visible light; performance also depends strongly on geometry, angle, distance, and acoustic properties. Soft materials may absorb sound and can also be difficult targets.

  5. Q1(e). The working principle of a potentiometer is based on: (i) Capacitance change (ii) Inductance change (iii) Magnetic flux variation (iv) Resistance variation20252m

    Module 2: Position and velocity measurment

    The working principle of a potentiometer is based on:
    (i) Capacitance change
    (ii) Inductance change
    (iii) Magnetic flux variation
    (iv) Resistance variation

    View this question on its own page →
    Worked Solution

    Correct answer: (iv) Resistance variation. A potentiometer is a variable resistor. Wiper position changes the resistance ratio and therefore the output voltage in a voltage-divider circuit.

  6. Q1(f). Which actuator is most suitable for heavy-load industrial robotic arms? (i) Pneumatic actuator (ii) Hydraulic actuator (iii) Electrical actuator (iv) Piezoelectric actuator20252m

    Module 4: Robotic actuators

    Which actuator is most suitable for heavy-load industrial robotic arms?
    (i) Pneumatic actuator
    (ii) Hydraulic actuator
    (iii) Electrical actuator
    (iv) Piezoelectric actuator

    View this question on its own page →
    Worked Solution

    Correct answer: (ii) Hydraulic actuator. Hydraulic systems can generate high force and torque from compact actuators, making them suitable for heavy-load industrial arms. They require pumps, fluid lines, seals, and leak control.

  7. Q1(g). Which sensor is commonly used for collision detection in mobile robots? (i) IR sensor (ii) Ultrasonic sensor (iii) Optical encoder (iv) Tactile sensor20252m

    Module 1: Sensor classifications and characteristics

    Which sensor is commonly used for collision detection in mobile robots?
    (i) IR sensor
    (ii) Ultrasonic sensor
    (iii) Optical encoder
    (iv) Tactile sensor

    View this question on its own page →
    Worked Solution

    Correct answer: (ii) Ultrasonic sensor is a common non-contact collision/obstacle detector in mobile robots. It estimates distance from echo time-of-flight; tactile sensors can detect contact after collision, while encoders measure motion.

  8. Q1(h). The primary function of an accelerometer in robotics is to measure: (i) Linear acceleration and tilt (ii) Angular velocity (iii) Orientation only (iv) Distance traveled20252m

    Module 2: Position and velocity measurment

    The primary function of an accelerometer in robotics is to measure:
    (i) Linear acceleration and tilt
    (ii) Angular velocity
    (iii) Orientation only
    (iv) Distance traveled

    View this question on its own page →
    Worked Solution

    Correct answer: (i) Linear acceleration and tilt. An accelerometer measures specific force. When stationary or moving slowly, the gravity component can be used to estimate tilt; during dynamic motion, gravity and motion acceleration must be separated.

  9. Q1(i). Which motor provides high torque at low speed without using a gearbox? (i) DC motor (ii) Stepper motor (iii) AC induction motor (iv) Servo motor20252m

    Module 5: Introduction to motors

    Which motor provides high torque at low speed without using a gearbox?
    (i) DC motor
    (ii) Stepper motor
    (iii) AC induction motor
    (iv) Servo motor

    View this question on its own page →
    Worked Solution

    Expected answer: (iv) Servo motor in the context of controlled high torque at low speed without a separate gearbox, although this depends on motor design. A direct-drive servo is specifically designed to deliver high torque at low speed; ordinary DC, stepper, and induction motors do not guarantee this without appropriate sizing/gearing.

  10. Q1(j). Belt drives are preferred over gear drives when: (i) Exact velocity ratio is required (ii) High torque transmission is needed (iii) Noise and vibration reduction is required (iv) Space is limited20252m

    Module 6: Motion transmission

    Belt drives are preferred over gear drives when:
    (i) Exact velocity ratio is required
    (ii) High torque transmission is needed
    (iii) Noise and vibration reduction is required
    (iv) Space is limited

    View this question on its own page →
    Worked Solution

    Correct answer: (iii) Noise and vibration reduction is required. Belt drives can run more quietly and absorb shock compared with gear drives. They may slip and are less suitable when a precise, constant velocity ratio is essential.

  11. Budget App•POCKETLY

    Pocketly on Android

    Log daily food, travel, and hostel expenses instantly. Set monthly spending limits and see where your money goes without complex spreadsheets.

    Install Pocketly
  12. Q2(a). Discuss the working principle, advantages, and disadvantages of IR sensors.20257m

    Module 1: Sensor classifications and characteristics

    Discuss the working principle, advantages, and disadvantages of IR sensors.

    View this question on its own page →
    Worked Solution

    IR sensor principle: An infrared emitter sends IR radiation and a photodiode/phototransistor detects reflected or interrupted radiation. In reflective sensors, received intensity changes with object distance, reflectivity, and angle; active IR distance sensors may use triangulation or modulated signals. Advantages: inexpensive, compact, fast, low power, useful for short-range proximity and line following. Disadvantages: affected by ambient IR, surface colour/reflectivity, sunlight, alignment, and range; simple intensity-based sensors give imprecise distance. Applications include obstacle detection, object counting, line-following robots, and proximity switches. Modulation and calibration improve reliability.

  13. Q2(b). Explain the pneumatic actuator with suitable examples.20257m

    Module 4: Robotic actuators

    Explain the pneumatic actuator with suitable examples.

    View this question on its own page →
    Worked Solution

    Pneumatic actuator: Converts compressed-air energy into mechanical motion. A compressor and regulator supply air through valves to a cylinder or rotary vane actuator. Pressure acting on piston area produces force: F = P×A (ideal, ignoring friction and pressure losses). Double-acting cylinders use air alternately on both sides for extension and retraction; single-acting types use a spring or external force for return. Advantages: clean, quick response, simple, inexpensive, and safe in some explosive environments. Limitations: air compressibility reduces stiffness/precision, force is lower than hydraulic systems, noise and air leaks occur, and compressors consume energy. Uses: grippers, pick-and-place mechanisms, clamping, and light-duty robot motion.

  14. Q3(a). Explain the working and application of Tactile Sensor.20257m

    Module 1: Sensor classifications and characteristics

    Explain the working and application of Tactile Sensor.

    View this question on its own page →
    Worked Solution

    Tactile sensor: Detects physical contact, pressure distribution, or slip at a robot finger or surface. A contact force deforms a sensing element; the transducer converts deformation into an electrical signal. Technologies include resistive/piezoresistive, capacitive, piezoelectric, optical, and conductive-elastomer arrays. An array can estimate contact location and pressure map; dynamic signals may indicate slip. Applications include robotic grasping, object recognition by touch, force-limited manipulation, prosthetics, and human–robot interaction. Desired properties include sensitivity, spatial resolution, repeatability, fast response, durability, and conformability. Limitations include drift, hysteresis, calibration needs, wiring complexity, and wear.

  15. Q3(b). Discuss belt transmission and compare it with gear transmission.20257m

    Module 6: Motion transmission

    Discuss belt transmission and compare it with gear transmission.

    View this question on its own page →
    Worked Solution

    Belt transmission: driver and driven pulleys transmit motion via a belt; friction belts may slip, while toothed timing belts provide more positive engagement. Compared with gears: belts are quieter, absorb shock, tolerate some misalignment, are inexpensive, and can span larger centre distances. They may slip/stretch, need tensioning, occupy space, and provide less exact ratio unless toothed. Gears provide accurate ratio, high torque density, and compact packaging, but require precise alignment/lubrication and may be noisy and costly. Choose belts for quiet, economical transmission; gears for precise timing and high loads.

  16. Q4(a). Explain gyroscopes and their use in robotics.20257m

    Module 2: Position and velocity measurment

    Explain gyroscopes and their use in robotics.

    View this question on its own page →
    Worked Solution

    Gyroscope: Measures angular rate about one or more axes. MEMS gyroscopes commonly use a vibrating mass; rotation produces a Coriolis force that is sensed electrically. Optical gyros use interference/phase shifts between counter-propagating light beams. Robot uses include orientation estimation, stabilisation, inertial navigation, drone attitude control, and sensor fusion with accelerometers/encoders. Integrating angular rate estimates angle, but bias and noise cause drift; calibration and sensor fusion (e.g. complementary/Kalman filtering) improve estimates.

  17. Q4(b). Discuss the types of stepper motors along with their advantages and disadvantages.20257m

    Module 5: Introduction to motors

    Discuss the types of stepper motors along with their advantages and disadvantages.

    View this question on its own page →
    Worked Solution

    Stepper motor types: (1) Variable-reluctance: toothed soft-iron rotor aligns to minimise magnetic reluctance; no permanent magnet, moderate torque. (2) Permanent-magnet: magnetised rotor interacts with stator fields; good holding torque. (3) Hybrid: combines toothed rotor and permanent magnet, giving finer steps and high torque. Advantages: precise incremental motion, strong holding torque, easy open-loop control, good low-speed performance. Disadvantages: can lose steps if overloaded, resonance/vibration, torque falls at high speed, and continuous holding consumes power and generates heat. Applications include printers, CNC positioning, and small robot axes.

  18. Q5(a). Explain force sensors. Discuss their types, applications, and limitations.20257m

    Module 3: Force and Torque measurment

    Explain force sensors. Discuss their types, applications, and limitations.

    View this question on its own page →
    Worked Solution

    Force sensors: Measure applied force, often using elastic deformation. Types include strain-gauge load cells (resistance changes with strain), piezoelectric sensors (charge under dynamic force), capacitive sensors (gap/area change), and optical force sensors. A strain-gauge bridge output is amplified and calibrated to force. Applications: robot grippers, force control, assembly, polishing, tactile interaction, and medical rehabilitation. Advantages include measurable feedback and safer compliant interaction. Limitations: calibration/drift, temperature sensitivity, hysteresis, overload damage, cross-axis sensitivity, and noise. Piezoelectric types are excellent for dynamic forces but generally not static force measurement without specialised circuitry.

  19. Q5(b). Explain torque sensors along with types and applications.20257m

    Module 3: Force and Torque measurment

    Explain torque sensors along with types and applications.

    View this question on its own page →
    Worked Solution

    Torque sensors: Measure rotational moment, τ = F×r for perpendicular force and lever arm. Strain-gauge torque sensors measure torsional strain on a shaft, often using gauges at ±45° in a bridge; magnetoelastic, optical, and piezoelectric approaches are also used. Rotary sensors may transmit signals via slip rings or wireless telemetry. Applications include robot joint torque feedback, motor/gear testing, tightening tools, and force-controlled manipulation. Important specifications are range, accuracy, resolution, bandwidth, overload capacity, temperature stability, and rotational signal transfer. Torque feedback improves control and helps detect collisions or excessive contact forces.

  20. Q6(a). Explain hydraulic actuators along with their advantages and disadvantages.20257m

    Module 4: Robotic actuators

    Explain hydraulic actuators along with their advantages and disadvantages.

    View this question on its own page →
    Worked Solution

    Hydraulic actuator: Pressurised fluid drives a piston or hydraulic motor. A pump supplies fluid; valves regulate direction/flow/pressure; a cylinder converts pressure to linear motion. Ideal cylinder force is F = P×A, and speed approximately v = Q/A (flow rate Q divided by piston area A). Advantages: very high force/torque, high power density, smooth controllable motion, and good load handling. Disadvantages: leakage and contamination, maintenance, noise, fire/environmental concerns with some fluids, bulky power unit, and potential fluid heating. Used in heavy industrial manipulators, presses, and high-load robotic applications.

  21. Q6(b). Discuss the working of proximity sensors with application in robotics.20257m

    Module 1: Sensor classifications and characteristics

    Discuss the working of proximity sensors with application in robotics.

    View this question on its own page →
    Worked Solution

    Proximity sensors: Detect an object without necessarily touching it. Inductive sensors detect metal by changes in an electromagnetic field; capacitive sensors detect changes in capacitance and can detect many non-metallic materials; optical/IR sensors use light interruption/reflection; ultrasonic sensors measure acoustic echo time; magnetic sensors detect a magnet or field. Applications include end-stop detection, object presence, collision avoidance, part counting, and robot gripper feedback. Selection depends on sensing distance, target material, environment, response time, accuracy, and cost. Limitations vary: inductive types mainly detect metal, optical types are affected by surface/ambient light, and ultrasonic types by target angle/absorption.

  22. Budget App•POCKETLY

    Pocketly on Android

    Log daily food, travel, and hostel expenses instantly. Set monthly spending limits and see where your money goes without complex spreadsheets.

    Install Pocketly
  23. Q7(a). Explain the working of DC motors and their applications in robotics.20257m

    Module 5: Introduction to motors

    Explain the working of DC motors and their applications in robotics.

    View this question on its own page →
    Worked Solution

    DC motor working: Current through armature conductors in a magnetic field produces force (F = BIL), creating torque. The commutator and brushes reverse armature current each half-turn in a brushed motor to keep torque in the same direction. Back EMF opposes supply voltage and rises with speed. Torque is approximately proportional to armature current; speed depends on voltage and load. Uses: mobile robot drive wheels, small manipulators, grippers, and auxiliary mechanisms. Advantages include easy speed control and high starting torque; limitations include brush wear, electrical noise, and maintenance. Brushless DC motors use electronic commutation.

  24. Q7(b). Discuss the applications, advantages, and disadvantages of ultrasonic sensors.20257m

    Module 1: Sensor classifications and characteristics

    Discuss the applications, advantages, and disadvantages of ultrasonic sensors.

    View this question on its own page →
    Worked Solution

    Ultrasonic sensors: Emit high-frequency sound pulses and measure echo time. Distance is d = vt/2, where v is sound speed and t is round-trip time. Applications: mobile robot obstacle avoidance, range finding, level measurement, and collision prevention. Advantages: inexpensive, non-contact, works in darkness, and detects many object colours. Limitations: soft/angled surfaces may absorb or deflect sound; narrow objects can be missed; temperature changes sound speed; multiple sensors may cross-talk; and minimum range/dead zone exists.

  25. Q8(a). Explain AC motors along with components, working, advantages, and disadvantages.20257m

    Module 5: Introduction to motors

    Explain AC motors along with components, working, advantages, and disadvantages.

    View this question on its own page →
    Worked Solution

    AC motors: Main parts are stator, rotor, air gap, frame, bearings, and (depending on type) windings/cage or permanent magnets. AC applied to stator windings creates a rotating magnetic field. In an induction motor, this field induces rotor current and torque; rotor runs below synchronous speed. Synchronous speed is Ns = 120f/P rpm, where f is supply frequency and P is pole count. Speed control commonly uses a variable-frequency drive. Advantages: robust, efficient, low maintenance, good for continuous duty. Disadvantages: speed control can require a drive, starting current can be high, and precise position control generally needs feedback/control. Used in robot auxiliaries and industrial motion systems.

  26. Q8(b). Discuss the construction and working of optical encoders.20257m

    Module 2: Position and velocity measurment

    Discuss the construction and working of optical encoders.

    View this question on its own page →
    Worked Solution

    Optical encoder construction: A light source, coded disk or linear scale, photodetectors, and signal-conditioning electronics. As the disk moves, slots/marks modulate light reaching detectors. Incremental encoders generate pulses; two quadrature channels (A/B) indicate direction and permit higher-resolution counting, while an index pulse provides a reference. Absolute encoders output a unique digital code for each position. For an incremental encoder with N pulses/revolution, angular increment is 360°/N (or smaller with quadrature decoding). Encoders provide position and derived speed feedback in servo control. Limitations include contamination, alignment sensitivity, and loss of absolute position after power-off for incremental types.

  27. Q9. Write short notes on any two of the following: (a) Hydraulic Drives (b) Potentiometers (c) Servo Motors (d) Laser Ranger Finder [7 marks each; attempt any two].202514m

    Module 4: Robotic actuators

    Write short notes on any two of the following:
    (a) Hydraulic Drives
    (b) Potentiometers
    (c) Servo Motors
    (d) Laser Ranger Finder
    [7 marks each; attempt any two].

    View this question on its own page →
    Worked Solution

    (a) Hydraulic drives: A pump pressurises fluid; valves control flow/direction and cylinders or hydraulic motors produce motion. They provide high force and power density, but require leak prevention, filtration, and maintenance. (b) Potentiometers: A resistive track and movable wiper form a voltage divider. Wiper position produces a proportional voltage for angular/linear position sensing. They are simple and inexpensive but have contact wear, noise, and finite life. (c) Servo motors: A motor, feedback sensor, and controller form a closed loop; the controller compares command with measured position/speed and drives the motor to reduce error. They provide accurate positioning and dynamic response but require tuning and feedback hardware. (d) Laser range finder: Emits laser light and estimates distance from time-of-flight or phase shift (some triangulation systems use geometry). It offers long-range, narrow-beam measurement but may be affected by reflectivity, weather, alignment, and eye-safety constraints. The exam asks any two, 7 marks each.

AI LearningWeb Platform

Coursify — Personal AI Course Generator

Struggling with a difficult subject or concept? Turn any engineering topic into a structured course with interactive lessons, quizzes, and research-backed explanations.